Home > Hard Drive > How To Slave A Sata Hard Drive

How To Slave A Sata Hard Drive

Contents

We just took it out and put it in an external drive, and it didn't run through a scan, but it didn't come up with anything different. mp3..etc. You would then need to format and load an os on that drive. If your drive has some type of major file system problem it may show up as "unknown". Check This Out

Ask us. If the BIOS doesn’t see the drive that means either the drive isn’t connected and jumpered properly or is in such bad shape that it isn’t seen by the BIOS. With XP and 2000, though, use Windows' Disk Management utility. Feel free to call us for a no obligation quote.

How To Slave A Sata Hard Drive

primate January 13, 2008 11:37 pm Reply # My Western Digital 2500 (from a Gateway) doesn't have an obvious slave setting. any help would be appreciated. With modern SATA, which is a serial bus instead of the older parallel EIDE bus, things are simpler.

Thanks again, and I'm sure I'll be back. What should I do? Get the answer Best answer ronintexasApr 3, 2013, 9:27 PM The Gray SATA connectors are the SATA III (6GB) connectors - should be used for the SSD. How To Slave A Hard Drive Gee, I should be without for what, about two weeks.

Our services are no data no charge so you only pay if we recover your files - and they work! How To Install A Second Sata Hard Drive Step 13: Now connect a free power connector to the hard drive. But the 2.5″ USB enclosure would be the easiest way to do it. http://www.wikihow.com/Add-an-Extra-Hard-Drive My Questions… 🙂 Can I still connect/mount everything if they are different formats?

DTI Data Recovery January 4, 2008 12:27 pm Reply # Perla, Yes this post shows how to slave a hard drive so that you can either copy data off, or if Master Slave Hard Drive Setup Pass?/Fail? the properties tab, says that everthing is working properly, Very weird. The external has its own backup software and stuff pre-installed.

How To Install A Second Sata Hard Drive

They'll have a couple of rubber or plastic blocks covering some pins. Deborah S September 3, 2008 5:05 pm Reply # Thank you Michael, I thought that was the way to go. How To Slave A Sata Hard Drive Here, we installed Seagate's Barracuda 7200.10, a $124, 320GB Serial ATA (SATA) drive, inside a Dell Dimension 8400 running Windows XP Home Edition. How To Install A Second Hard Drive Windows 10 I have lot of photo inside the hard disc.

Is there any advice you can give me on making this the easiest, most painless process possible? http://faviconize.com/hard-drive/how-to-install-a-second-hard-drive.html It mentions that I have 111 GB of space available-not good since it was nearly full when it was working properly. My Western Digital showed in a diagram how to move the jumper to make the slave work properly. In regards to the Maxtor above the USB device will get recognized in Windows. How To Install A Second Hard Drive Windows 7

Either buy an external IDE hard drive case ($25-75), or simply open up your case, set the drives jumpers to slave or cable select, disconnect your cdrom drive, connect those cables I did get my hands on a USB enclosure for a 2.5 SATA drive. My Win XP crashed, and I have an old Win 98 back up. this contact form Order won't matter.

In fact that is a good idea for people that have an old drive that is working. How To Slave A Hard Drive To Recover Data In fact having restore disks greatly eases the burden of re-installing everything. Warnings This guide is not intended for Macintosh computers.

CompUSA should have both of these items in stock, but I would call first to make sure.

Get the answer Y0GIOct 30, 2013, 11:12 PM Bigfatmeany said: redguy54 said: Unless you can boot from it, I'm pretty sure you would need some recovery software. PLEASE do this gingerly as you do not want to damage any other internal components. Therefore I DO NOT WANT TO FORMAT the drive unless this means something other than deleting all the files currently on the disk. How To Slave A Laptop Hard Drive TJ Helpful +1 Report tjmartineau 38Posts Friday September 19, 2008Registration date December 23, 2008 Last seen Sep 27, 2008 at 07:20 PM Don't have the dvdrom connected at all, just have

Note that you may need to leave the old one in temporarily to transfer your data onto the new one. Report cheefdapot- Jan 9, 2009 at 11:48 AM dude!!!! Is there a way to erase the external hardrive and reformat so that it can be used again? navigate here Video Tips Try to use SATA drives instead of IDE because they are usually faster and the wide ribbon cable for IDE drives blocks airflow.

I created a logical partition with PM which could then be seen by DOS and Windows. Bought a 320GB Seagate barracuda (70 bucks!). The problem has to be with my version of XP. IDE drives use a wide, flat ribbon cable and may have jumpers that need to be set.

Do I need a data recovery program? So the question is Im going to build the laptop back up with a new hard drive. The dreaded BSOD popped up, I'm running XP Professional. It could just be a corrupt file the local fix-it shop says.So when I use the usb thing with my laptop harddrive inside it, to hook to my desktop or another

I own a copy of Partition Magic and I wondered if PM could do it. or would i have to back up my files and then reinstall my OW? guy said he would look at it for me but I dont want him or any one else going through my files. The light on the power button lit up, but the computer did not start.

That is about as big a store as I am going to get around here…. About CNET Privacy Policy Ad Choice Terms of Use Mobile User Agreement Help Center could you walk me through the computer management assessment? I was able to retrieve all data from the WinXP slave drive using Win98 as the master.

Is your only objective here to surf the internet and NOT have to format the disk? IT COULD!!!! Yikessssssssss Jacqui Best January 10, 2011 3:24 pm Reply # Rich, A lot of times the files are going to be in a USER profile and be inaccessible. or is this just so i can copy my old info onto the new computer?

Well we gave it about five mins and nothing came up. On Intel boards, for example, SATA II ports tend to be black; SATA III ports are blue. If the Win XP machine has Win XP Professional, then it has a NTFS file system that Windows 98 will not reconize, and therefore will not work. The fact that your laptop sees the drive means that you can use data recovery software to recover the files, even though Windows want to format the drive.